Payment & Shipping Terms:
|Working Frequency::||230MHz||Data Transmission Rate::||1200/2400/4800bps|
|Receiving Sensitivity::||≤-119dBm||Transmission Power：:||≤500mW|
wireless data module,
wireless transceiver module
230MHz Wireless Data Module 500mW Radio Data Link RS-232/RS-485/TTL Interface
1. High stability, high reliability, low cost data transmission
2. Provided standard external interfaces(RS-232/RS-485/TTL)
3. Easy installation and maintenance, strong diffraction ability, flexible network structure, small coverage etc.
4. Suitable for multi-point and scattered, complex geographical applications
5. Widely used in electricity, meter reading, environmental protection,warehouse management, PTZ control, alarm, GPS positioning information back, GIS and other areas monitoring, data real-time transmission etc.
6. Satisfy clients requirements for real-time and accurate data.
|Overall Index||Working Frequency: 230MHz||Frequency Tolerance:±5ppm|
|Channel Spacing: 25KHz||Antenna Impedance:50Ω|
|Environment Temperature:-25℃～+55℃||Data Transmission Rate:1200/2400/4800bps|
|Receiving Index||Receiving Sensitivity:≤-119dBm(better than 12dB SINAD)||Remaining Level:≤-45dB|
|Modulation Bandwidth:≥5KHz||Adjacent channel selectivity:≥65dB|
|Transimission Index||Transmission Power: ≤500mW|
|Adjacent-channel Power Ratio: ≥70dB||Spurious RF component: ≤-70dB|
|Working Current: ≤300mA|
|Dimension||Device Dimension:70×46×12mm||Antenna Interface:SMA-50 Ohm|
|1#||Vcc||Power 5 ~ 12V|
|2#||Vcc||Power 5 ~ 12V|
|5#||RXD(A)||Radio data reception /485A|
|6#||TXD(B)||Radio data transmission/485B|
|10#||SQ||Receipt Signal Indicator|
|8N1||1 start bit + 8 data bit +1 stop bit, no parity|
|8E1||1 start bit + 8 data bit +1 stop bit + even parity|
|8Q1||1 start bit + 8 data bit +1 stop bit + odd parity|
|It is receiving state when power standby ; When the data port detects a data input, the radio automatically transmits. After the data transmission, it turns to receiving state.|
|1||Adopt small rippled and stablized power supply or battery.|
|2||The antenna should be kept away from the power supply.|
|3||Power supply capacity should meet 5/12V/500mA|
|4||The distance between the experimental stations should be farther than 5 meters|
|5||Install the Antenna in high place, no shelter within 30 meter coverage|
|Tips: After the radio connected to the antenna, the distance between the radios should be more than 10 meters to avoid too strong signal caused blocking!|
1Use the min. grain wave and high anti-jamming switch power or batteries;
2The power capacity must meet D.C. 5~12V,more than 800mA output current
3The space between the experiments Radio should be more than 5m. The antenna should span on the high to increase the distance of electric wave. It is important for using shortwave communication equipment in the city.
4After connecting the antenna to the Radio, the space between the Radios should more than 10m, so avoid signal backup.
5The antenna plywood should nip in the connection inside the antenna, but not nip the antenna projectile, so avoiding the performance of the antenna.
High frequency cable don’t come down directness, circle a circuit and fix up it on the frame for the best.
UHF Digital Long Range Video Transmitter , 1080P HD Wireless Video Sender 40 Watt RF
Digital Wireless Long Range Video Audio Transmitter NLOS Fast Moving Transmission AES 128 / 256 bits
1080P HD Long Distance Video Transmitter Data Encryption Wireless AV Communication
1-3W IP Mesh TDD Transceiver COFDM Bidirectional Portable Radio Downlink Uplink Up to 16 Nodes
NLOS COFDM IP Mesh 16 Nodes Long Range Microwave Wireless Mesh Network
RS-232/RS-485 Network Video Transceiver , Wireless HD Transmitter Two Way Transmission
CCTV Wireless Analog Video Transmitter 8 Watt RF Power Real-time Transmission
5.8Ghz 5 Watt Wireless Video Sender Waterproof Video Transmitter and Receiver Long Range
AC 220V Long Range Hd Video Transmitter 10W CCTV Surveillance Wireless Transmission